Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: Bell Crank (shifter) for '61 Evinrude 75 Hp

Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 3 months ago #119402

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
My Starflite III shift linkage is worn and one of the parts I need to replace is the bellcrank. I haven't been able to locate one through the usual sources (Marine Engine.com, Ebay). Can anyone give me a suggestion of a possible source? Thanks.

Doug

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 3 months ago #119409

  • ed-mc
  • Offline
  • Platinum Boarder
  • Platinum Boarder
  • Posts: 1395
  • Karma: 232
  • Thank you received: 114
Did you try Seaway Marine in Lynwood, Wa? They have extensive old-stock parts and might have something kicking around.

www.seawaymarine.com/

Failing that, there's almost always a dead V4 parts motor on the Craigslist somewhere nearby!.

HTH & G'luck........ed

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 3 months ago #119427

  • 63 Sabre
  • 63 Sabre's Avatar
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 4676
  • Karma: 147
  • Thank you received: 167
Doug, put up a picture of all you need. I have the entire shift linkage setup for a '59 75hp starflite III. all cleaned and bagged.
Cal

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 3 months ago #119437

  • VinTin
  • VinTin's Avatar
  • Offline
  • Senior Boarder
  • Senior Boarder
  • Posts: 188
  • Karma: 13
  • Thank you received: 2
63 Sabre wrote:

Doug, put up a picture of all you need. I have the entire shift linkage setup for a '59 75hp starflite III. all cleaned and bagged.
Cal


I'm pretty sure the largest OMC motor in 1959 was 50hp.

First year for the 75hp was 1960.

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 3 months ago #119450

  • 63 Sabre
  • 63 Sabre's Avatar
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 4676
  • Karma: 147
  • Thank you received: 167
I stand corrected. It is a 1960. Either way I have the entire linkage if needed.
Attachments:

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 2 months ago #119535

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
I haven't taken everything off as yet. I've had the lower unit off along with the linkage from the external shift lever to where it connects to the engine block. Have been reluctant to go after the bellcrank as I'm not really experienced with engine repair (I take lots of pictures as I go!) I'm going to try one more adjustment of the point where the upper and lower linkages connect on the port side of the lower unit. Any feeling for how long your parts were actually in use? How much for the whole lot? Doug

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 2 months ago #119536

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
PS Message me on Facebook if you prefer. Full name is Doug Speck in Gaines, Michigan.

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 2 months ago #119543

  • 63 Sabre
  • 63 Sabre's Avatar
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 4676
  • Karma: 147
  • Thank you received: 167
Doug, I've no idea of how long these were in use. I purchased the motor for parts and still have lots of them left over. As you can see in the pictures they are not worn.
Take your time and lots of pictures. If you decide it's what you could use let me know on this thread or you can message me on this site also. I think $25 for the complete linkage set that is in the picture is fair. Or....make me an offer but gotta include shipping costs.

Please Log in or Create an account to join the conversation.

Re: Bell Crank (shifter) for '61 Evinrude 75 Hp 8 years 2 months ago #119722

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
Thanks, I will. Sorry for the delay, but have been enroute to Florida to escape the snow and cold for awhile. I'll be in touch.

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.197 seconds

Donate

Please consider supporting our efforts.

FG Login

Glassified Ads

The Pink Lady
( / Boats)

The Pink Lady
05-02-2024

Gator 9" wheels Wanted
( / Wanted)

noimage
04-24-2024

1969 Stern Craft Boat 19'
( / Boats)

1969 Stern Craft Boat 19'
04-08-2024

FiberGoogle

Who's Online

We have 4022 guests and no members online